Frequently Asked Questions
AeroBarrier may be applied at any time between after framing inspection is complete and prior to occupancy. Although, the ideal time to apply AeroBarrier is post-drywall. Other factors that effect install is build process and climate zone.
No, just like one would not enter an active paint booth without wearing personal protective equipment (PPE), similar to those worn by painters when spray painting. During application, if a technician has to enter the space while it is being sealed they wear PPE. After the sealing is complete, the area is safe to enter without protective gear within 20 to 30 minutes.
The AeroBarrier sealant is based on a waterborne acrylic that has been used as a fluid-applied permeable air barrier for many years. The sealant is GREENGUARD Gold-certified and has been tested according to various ASTM standards and NFPA 285, for fire spread, smoke production, adhesion, antifungal properties, tensile strength, etc.
The sealant is low VOC and has no off-gassing.
The entire AeroBarrier process, from setup to completion, takes approximately 4 – 6 hours for a typical single-family home. When targeting reduced envelope leakage levels of Passive House or ZERH, additional time may be required.
Cost will depend on the construction phase and targeted air tightness levels. Once we have your job specifications (size of home, existing airtightness level, etc), we provide a written quote within 24 hours. Call us at 604-222-2100 or email us at firstname.lastname@example.org to talk about your project.
All new houses in BC require a ventilation strategy in place to make sure fresh air is brought into the house so this won’t be an issue. In a majority of the cases, a Heat Recovery Ventilator (or HRV) is the mechanical appliance that is installed to exhaust stale air and draw in fresh outdoor air, providing for higher indoor air quality.
Third-party lab testing reveals AeroBarrier withstands a simulated 50-year durability test, with little or no seal degradation.
AeroBarrier seals holes as large as ½”, and as tiny as a human hair. Aerosol sealing is extremely effective at sealing narrow gaps and extremely small holes that are typically not cost-effective or are missed during manual sealing.
If AeroBarrier is applied at rough-in or right after drywall is installed, there in very minimal preparation required. Vertical surfaces like walls and windows require no covering. All designed openings, such as ducts, electrical and plumbing, need to be covered prior to sealing. All finished horizontal surfaces need to be covered.
The AeroBarrier process requires temperature control and pressurizing the areas to be sealed. Ideal conditions is an outdoor temperature of ≥ 5˚C. Sealing can be done below 5˚C but may require additional steps for the preparation.
Yes, the AeroBarrier sealant is GreenGuard Gold Certified, meaning that it is both safe to be used inside a home, and also meets the stricter certification requirements for use in schools and healthcare facilities as well.
The area needs to be aired out for 30 minutes after the sealing is complete. This is done by opening doors and windows while running the fan. But work can resume in the space as soon as the sealing equipment is removed and 30 min has passed.
The AeroBarrier system uses a standard blower door device to measure envelope leakage in real-time during the process. The system tracks air leakage using three different metrics: Normalized Leakage Area (in square inches), Leakage Volume Rate (in cubic ft/min or CFM) and Air Change per Hour at 50 Pascals of pressure (or ACH50).
The blower door device is calibrated to meet ASTM Standard E779, E1554, CGSB-149.10-M86, EN 13829, ATTMA Technical Standard 1, NFPA 2001, RESNET and USACE.
Schedule AeroBarrier for your Upcoming Project
Contact us if you have a project in Greater Vancouver where you’d like to apply AeroBarrier, or if you have any questions or comments for us.
Pacific Aerobarrier team assists builders in Greater Vancouver. This includes Vancouver, North Vancouver, West Vancouver, Burnaby, Richmond, Surrey, New Westminister, Port Coquitlam, Coquitlam, and Langley
Follow us on Instagram